AAP Industries PEAL® Black Mild Steel Bevel End Bend 90 Degrees

* Bevel bends are subject to manufacturers specifications only. (Length and radius may vary)

Black Mild Steel Bevel End Bend 90 Degrees
AAP CODE	IMPERIAL SIZE	APPROX. A	APPROX. R	APPROX. (KG/PC)
SBDW15	1/2	86	57	0.18
SBDW20	3/4	102	73	0.31
SBDW25	1	121	89	0.58
SBDW32	1 1/4	146	108	0.89
SBDW40	1 1/2	165	127	1.14
SBDW50	2	203	159	1.87
SBDW65	2 1/2	248	197	3.30
SBDW80	3	292	232	5.16
SBDW94	4	381	308	9.97
SBDW96	6	622	440	28

[1] PEAL STEEL FITTINGS

Specifications

H/6 r

STEEL THREADED PIPE FITTINGS MANUFACTURED ACCORDING TO THE BS EN 10241:2000 STANDARD. NORMATIVE REFERENCES: EN 10204, EN ISO 6708, ISO 7-1 PART 1, ISO 7-2, PART 2, AS 1074.

British Standard Threads
All measurements in mm
NOMINAL BORE OF PIPE		APPROX. OUTSIDE DIAMETER	NUMBER OF THREADS PER INCH	PITCH	DEPTH OF THREADS	DIAMETER AT GAUGE PLANE	LENGTH OF USEFUL THREAD
IMPERIAL	METRIC	A		P	h	B	E
1/8	6	10.16	28	0.907	0.581	9.72	6.5
1/4	8	13.66	19	1.337	0.856	13.15	9.7
3/8	10	17.17	19	1.337	0.856	16.66	10.1
1/2	15	21.51	14	1.814	1.162	20.95	13.2
3/4	20	27.00	14	1.814	1.162	26.44	14.5
1	25	33.93	11	2.309	1.479	33.24	16.8
1 1/4	32	42.59	11	2.309	1.479	41.91	19.1
1 1/2	40	48.48	11	2.309	1.479	47.80	19.1
2	50	60.47	11	2.309	1.479	59.61	23.4
2 1/2	65	76.09	11	2.309	1.479	75.18	26.7
3	80	88.87	11	2.309	1.479	87.88	29.8
4	100	114.14	11	2.309	1.479	113.03	35.8
5	125	139.65	11	2.309	1.479	138.43	40.1
6	150	165.12	11	2.309	1.479	163.83	40.1

Chemical Composition of Seamless Steel Fittings
C MAX. (%)	S MAX. (%)	P MAX. (%)
0.25	0.35	0.09

Chemical Composition of Fabricated Fittings
C MAX. (%)	Mn MAX. (%)	P MAX. (%)	S MAX. (%)
0.25	1.40	0.045	0.045

Mechanical Properties of Seamless Steel Fittings
TENSILE STRENGTH MIN. (N/mm2)	ELONGATION MIN. (%)
320	20

Mechanical Properties of Fabricated Fittings
TENSILE STRENGTH MIN. (N/mm2)	YEILD STRENGTH MIN. (N/mm2)	ELONGATION MIN. (%)
320	195	20

Black & Galvanised Steel Unions - Taper Threads

Black steel unions are used in a wide range of make-and-break joints such as: filters, valves, hoses, machinery and general piping installations requiring periodic disconnections. They are particularly suited to high or low pressure assemblies in air, oil, gas and water. They are available in Steel-Steel, Steel-Bronze and Bronze-Bronze seats with Female-Female and Male-Female end connections.

These unions are electro zinc plated and are available in Steel-Steel, Steel-Bronze and Bronze-Bronze seats with Female-Female and Male-Female end connections. This process gives a complete coating both externally and internally which protects the pipe union at the thread and vital seating areas. They are particularly suitable where there is condensation, such as in air and gas lines. The zinc coating also gives an outside protective coating against rust when exposed to the atmosphere. (The Steel-Steel zinc coated union is an ideal union suitable for most applications where vibration and moisture are present, such as compressed air lines and railway breaking systems)

Ball to Cone Seating in the following combinations:-

STEEL – STEEL (SS)

This is a general purpose combination recommended where vibration is present. The seats are integral and therefore are the most economically priced. This union will suit almost any application. Zinc coating improves the corrosion resistance of the joints to a marked degree where corrosion is present.

STEEL – BRONZE (SB)

A good seat combination where corrosion due to the fluid medium that is being used in the line or where condensation is present and when periodic disconnection is required. Zinc coating improves the corrosion resistance of the joints to a marked degree where corrosion is present.

BRONZE – BRONZE (BB)

This seat combination is recommended when corrosion due to the fluid medium in the pipe line or condensation is a major factor and where constant disconnection is required. This seat combination is ideally suited to steam lines. Zinc coating improves the corrosion resistance of the joints to a marked degree where corrosion is present.

END CONNECTION THREADING

- Taper threads only. External (R) and internal (RC) series to AS 1722 Part 1.

C=A/F

B=A/F

Peal ® Steel Unions

Zinc-Coated Unions

Seating Specifications

NOTES: 1. Dimension B-Nut is Hexagon up to DN 25 Nut is Octagon DN 32 and larger. 2. Dimension C-Body Flats are all Octagon.

3.* Dimensions A & E are approximately Overall length in mm.

PEAL STEEL FITTINGS [1]

AAP Steel Fittings are pressure tested by application of internal pressure, under which they are required to withstand, without signs of leakage, failure, or plastic deformation, the following tests *All sizes of unions up to 2” nominal bore individually tested to 13.8MPa and sample tested to 20.7MPa *All sizes of unions over 2” nominal bore individually tested to 10.3MPa * All sizes of ordinary sockets sample tested to 5.2MPa *All sizes of other fittings sample tested to 5.2MPa

C=A/F

B=A/F

Dimensions - mm
DN	8	10	15	20	25	32	40	50	65	80	100
A*	56	57	66	77	84	98	110	116	138	154	165
B	35	35	42	52	61	76	83	101	120	136	163
C	21	21	26	34	40	50	56	70	86	103	127
E*	42	42	46	54	61	71	82	88	108	119	121

Your name *

Your email *

Subject: *

Enquiry *

Irrigation Unit Conversions

Convert a given value and unit to different unit type. Conversions are available for flow rate, area, distance, time, volume, pressure, power, precipitation, salinity, and speed.

Click here to see unit descriptions.

Flow Rate:
		to

Area:
		to

Distance:
		to

Time:
		to

Volume:
		to

Pressure:
		to

Power:
		to

Precipitation (Water Application) Rate:
		to

Salinity:
		to

Speed:
		to

Reference: Washington State University

Dimensions - mm
DN	8	10	15	20	25	32	40	50	65	80	100
A*	56	57	66	77	84	98	110	116	138	154	165
B	35	35	42	52	61	76	83	101	120	136	163
C	21	21	26	34	40	50	56	70	86	103	127
E*	42	42	46	54	61	71	82	88	108	119	121

Dimensions - mm
DN	8	10	15	20	25	32	40	50	65	80	100
A*	56	57	66	77	84	98	110	116	138	154	165
B	35	35	42	52	61	76	83	101	120	136	163
C	21	21	26	34	40	50	56	70	86	103	127
E*	42	42	46	54	61	71	82	88	108	119	121